NEW ANNOUNCEMENT: Free domestic shipping on $50+ orders
0 Cart
Added to Cart
    You have items in your cart
    You have 1 item in your cart
    Total
    Check Out Continue Shopping

    Here is the HummingBird F4 Pro 1S: The second generation of the HummingBird F4 products. Compared to the 1st Generation, we changed the Gyro to Bosch BMI160 which is smaller and more reliable compared to the MPU6000. (It can't use the same firmware target as the 1st Generation HummingBird F4 1S.) We also changed the camera plug to have a JST 4 pin (OSD Signal, BeeSign signal, 5V, GND) so now you can either use BeeSign Control or BeeSign OSD (more explanation of the BeeSign is down below.) Also, we upgraded the propeller to the newest Azi Quad Blade 31mm Super balance Prop. Last but not least, we also optimized the layout and increase the high current layout trace to handle more power.


    Dry Weight 22g

    Camera Specs:

    • 25mw VTX, non-switchable power
    • Total weight with Goober canopy: ~4.9 gr. 120 FOV 700 TVL


    Wiring Diagram:

    This Kit Includes:

    FC Specification:

    • STM-F411 MCU for the main controller (Preloaded with BetaFlight)
    • Support 1S battery ONLY
    • Current sensor onboard
    • ESC-12A Per Motor Channel BB21 MCU
    • BlHeliS Support DShot(150 300 600) Multishot
    • Gyro-BMI160
    • Onboard Sideway RGB LED controlled by Betaflight
    • Support BeeSign signal compatible with NBD VTX-Camera System
    • Onboard Diversity SPI CC2500 Receiver(Frsky D8 D16, Futaba S-FHSS)
    • MotorPlug JST1.0
    • NBD OSD(Betaflight OSD Compatible)
    • 5V 1A Power support for external VTX Camera or Receiver.
    • Weight: 3.77g include power cable and PH2.0 Plug
    • Use Uart2 when connecting external RX


    BeeSign:

    BeeSign OSD uses Mark2 MCU to simulate an OSD chip. BeeSign OSD is used to communicate between the flight controller and the onboard VTX OSD (NewBeeDrone Mark 1,2,3 Series Video Transmitter). The BeeSign OSD protocol is a non-stop communication signal whereas the BeeSign Control is passive.

    BeeSign Control: Compared to BeeSign OSD, the BeeSign Control is a lighter version that only sends signal during VTX setting changes. Using BeeSign Control, the OSD signal comes directly from the flight controller.

    Although BeeSign requires a lot of information of the controller to go through one single wire, BeeSign OSD only needs a BeeSign signal wire, a GND wire, and 5V power to reach the Mark2 VTX board.

    Note: Beesign uses UART1 port. Do not use this port for other peripherals.

    Firmwares

    *Warranty Disclaimer: This product is designed to be bind-and-fly. Any modifications including soldering or flashing firmware will void your warranty.


     

    Review VideoÔºö

    Customer Reviews

    Based on 25 reviews
    60%
    (15)
    12%
    (3)
    12%
    (3)
    4%
    (1)
    12%
    (3)
    d
    d.
    Loving them whoops

    This is my second unit . It’s fast and easy to setup and newbee drone is always been fast in shipping and havin great customer support .It’s a great pratice drone to learn all about fpv despite all the crazy crashes even my old one is good and workin just wanted an xtra spare unit for Valentine’s days special 🤣🤣🤣.

    P
    P.A.
    NewBeeDrone Hummingbird F4 Pro

    Awesome Bird! This is my second one.

    E
    E.M.
    Hummingbird f4 brushless

    The drone is great tune is awesome the cam is crap I already ordered like 3 of the the issue is the vtx to cam solder is getting loose after 2-3 crashes currently I’m using betafpv c01 cam and their tiny vtx that holds up pretty good and cost less

    J
    J.C.
    Great little whoop

    Pretty new at this. Once I got it bound it flies really well. Even if I do crash a lot.

    L
    L.W.
    My 2nd favorite in the squad

    It's a pretty cool little whoop. The frame is fantastic. The camera, not so much. It's dynamic range suffers in my dim apartment, as it has trouble discerning between light and dark. Lights completely blow out to the point of no detail. It hovers higher in the throttle than my mobula6, but the 4 blade props are very stable and help it recover quickly. Mine doesn't have the antennas coming out of the canopy as it shows on the website. It also has a much shorter flight time than the mob6, but it's just stock and the mob6 has been flashed with jesc 48k. It was also half the price, since I got it on sale. The camera resolution is worse and the domed lense gives a fisheye effect. I don't dislike it, and it was definitely worth the price I paid, but it's not my favorite, either. The leds look dope af. I'd recommend it for the sale price, but if I'd paid the regular price, I might be less enthusiastic. I'll fly it over the moblite7, and the meteor75. I love the guys and girls at newbeedrone, and I'll continue to support their shop and will definitely look at more of their products in the future. 🙌

    Related Products

    View more