The AOS 7 EVO is a lightweight drone designed with low-vibration technology. This drone features state-of-the-art electronics and topology optimization. The AOS 7 EVO allows you to run less filtering, with less associated delay, and increase your PID gains far higher than any other frame in its weight class. Designed to match and even exceed the vibration performance of premium 5" frames this frame can deliver thrilling freestyle performance and long range cruising, the best of both worlds.
Highlights
DJI O3 HD Air Unit Low-Latency Digital Transmission
Topology-optimized truss design arms
2.5mm Top and Bottom Plates
Optimized Camera Protection
32x32 GoPro Mounting
Built by iFlight
Low Vibration
Specifications
Product Name:AOS 7 EVO V1.2 HD BNF
FC: BLITZ F722 FC
ESC: BLITZ E55 55A 4-IN-1 ESC
Video Transmission: DJI O3 Air Unit
Frame: 293mm wheelbase
Motor: XING 2806.5 motors
Prop: GemFan 7040 propellers
Takeoff Weight: Approx. 652g
Dimensions (L×W×H):284×228×34.5 mm
Max Speed:140 Km/h (Manual Mode)
Maximum Takeoff Altitude: 7000 m
Max Hover Time: Approx. 30 mins (With 6S 2P 8000mAh battery no load)
Max Wind Speed Resistance: Level 6
Operating Temperature Range:-10° to 40° C (14° to 104° F)
Antennas: Dual Antenna
GNSS: GPS+Galileo
Video Transmission
Product Name: DJI O3 Air Unit
Communication Bandwidth: Max 40 MHz
FOV (single screen): 155°
Communication Frequency: 2.400-2.4835 GHz (RX only) / 5.725-5.850 GHz (RX and TX)
End-to-End Latency
With DJI FPV Goggles V2:
810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.
With DJI Goggles 2:
1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.
Max Video Transmission Bitrate: 50 Mbps
Max Video Transmission Range: 10 km (FCC), 2 km (CE), 6 km (SRRC)
Operating Temperature Range: -10º to 40º C (14° to 104° F)
Power Input: 7.4-26.4 V
Audio Transmission: N/A
Packing List
1 x AOS 7 EVO V1.2 6S HD BNF
2 x Antennas
2 x Prop(Pairs)
Important
All iFlight BNFs are tested before shipment to guarantee the highest quality.
If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.
Note
1. iFlight products may be used for civilian purposes only and any direct or indirect use of iFlight products for or in connection with the following is prohibited:
(1)Any military combat purpose or military combat related use;
(2)Terrorist activities: The purchaser also shall require its customers or end users to comply with the foregoing requirements.
2. If party A has violated applicable export control or economic sanctions laws and regulations, Party B has the right to immediately suspend delivery of products to Party A or terminate relevant cooperation without any liability.
Right away, this is the best 65mm Whoop I know. Not even close.
I ordered two, one is more or less stock, just the PEEK motor screws and V3 cockroach. The second is upgraded to 0702 27000kV but will go back because I like the 25000kV more because of smoother throttle response and perfect betaflight tune.
Now the but:
1. On both quads I had to replace the BeeEye for a spare one because both are out of focus.
2. the yellow props were way too loose and very brittle. I lost two on my maiden. Black, blue and red are very tight (too tight for such a fragile prop) but if you get them on without bending them, they will last.
3. why does the quad not come with the lighter frame right away?
4. PH2.0…. You know the drill.
On that price point, even after the frame and PEEK upgrade I can forgive these quality issues. Especially considering the great tune and quality FC and motors. But be sure to order a replacement cam and props right away.
This was kind of a late night lark. I'd seen this upgrade for the Mk3 for a while and pondered whether it was a gimmick or not, and I'm pleased to say it's a genuinely good upgrade. It has reduced the noise of my Mk3 considerably. I haven't noted any significant increase in print quality, but the old drone of the bed is gone and that's completely worth it.