Exceptional flight performance. Lightweight. Ultra-low vibration. Easy to maintain. This is state-of-the-art FPV V2.0.
When I set out to create a bind and fly version of the AOS 5 V2 I had a vision to combine the latest and greatest technology into the ultimate FPV freestyle machine. This is the result. - Chris Rosser, AOS RC
Frame: The AOS 5 V2 has been designed to deliver the ultimate freestyle flight experience. The unique arm geometry has been refined through topology optimization to deliver maximum strength and stiffness for minimum weight. The same technology is used to optimize aircraft, satellites and race cars.
Motors: Exhilarating speed, silky smooth flight after flight. iFlight's XING2 2207 motors provide power and durability with a 7075 Aluminium unibell design, 5mm titanium shaft, Japanese NSK bearings, N52H center slotted arc magnets, and an integrated o-ring for bearing protection.
Electronics: Blazing fast with less filter delay for a more locked-in flight feel. The F7 flight controller takes maximum advantage of the vibration performance of the frame with a custom filter tune to reduce latency and improve propwash handling. With OSR4 mode enabled in BF4.3 the BMI270 gyro delivers latency and noise performance that matches or exceeds that of the MPU6000. A BLHeli32 ESC smoothly delivers power to the motors and the massive 55A rating ensures the motors will have all the power they could ever need.
Key features:
32x32mm GoPro mounting holes in top plate with installed press-nuts
Designed for up to 5.1 inch props, no props in view
Mount pattern: 20x20 mm / 4mm PCB hole diameter, silicon grommets for M3 screws
Smartaudio / IRC Tramp VTX protocol supported
Firmware target: IFRC-IFLIGHT_BLITZ_F722
Motor outputs: 4x (SH1.0 connector)
Flash: 16MB (Blackbox flash)
I2C serial: SDA / SLA pads
Dimensions: 30.5x27 mm
MCU: STM32 F722
Barometer: DPS310
OSD Chip: AT7456
LED controller: Yes
Beeper pad: Yes
Gyro: BMI270
Weight: 5g
UARTS: 6
ESC // BLITZ Mini 55A (Barcode:BE11376）
Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
Mounting Holes: 20*20mm/Φ4mm
Target: IFLIGHT_BLITZ_G2
Supports 2-6S lipo input
Dimension: 35*42mm
Current sensor: Yes
Firmware: BLHeli 32
Constant: 55 Amps
Current rate: 100
BlackBox: 16MB
Burst: 60 Amps
Weight: 11.3g
MCU：G071
BEC: NO
AOS 5 V2 HD Included Components and Parts
4 x Nazgul F5 - CW propeller + 4 x Nazgul F5 CCW (Grey)
1 x Albatross LHCP 5.8GHz SMA FPV Antenna 75mm
1 x Pre-built and Tested AOS 5 V2 HD BNF
1 x iFlight Lipo Strap 20*250mm (Black)
1 x iFlight Lipo Strap 15*250mm (Black)
1 x Nebula Pro Vista HD System
Note:
All iFlight BNFs are tested before shipment to guarantee the highest quality.
If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.
iFlight takes no responsibility for issues with DJI or Caddx 3rd party gear (Video transmitters, Goggles, Radios, etc) and must be directly reported to www.caddxfpv.com/pages/contact-us or www.dji.com/support.
I was pretty impressed with the construction of this drone. I've run four packs through it and have had some rough landings but this thing is solid. The battery connector is well placed, just a little short to allow for quick connections/disconnections. The BNF runs props out, so you'll want to remember that when you set it up. Hoping to get an AOS 7" and 3.5" CINE in the future.
I have flown the aos 3.5 frame for a little while now, and I’m loving it! I’m not sure about the durability yet, but I have crashed it and it’s holding up well so far! The flight characteristics are amazing, it’s super stable and easy to tune!
Love this little thing. I love this cause you can fly this rig over people due to the weight regulations ! It’s kind of hoppy indoors if you don’t have good throttle control.
Definitely recommend this esc for its reliability and value. Great performance, can adjust the pwm way up to 128 if needed. Runs great on my 6s 5.5" freestyle quad (auw 725g).
