Notes： SPI Frsky version comes with Betaflight 3.5.7 firmware in order to get better RSSI range . Bind code is “Frsky_bind” in the CLI Command SPI Flysky version comes with Betaflight 4.2.2 firmware . Bind code is “Bind_rx” in the CLI command SPI DSMX version comes with Customized Betaflight 4.3.0 firmware . Bind code is “Bind_rx” in the CLI command. The receiver firmware of RXSR version is R-XSR_FCC_190311 that is not compatible with ISRM v2.x.x , use ISRM V1.1.3
Features: 41gram 1-2s brushless Toothpick drone New AIO 4in1 CrazybeeX flight controller CADDX ANT Camera New 1202.5 brushless motor XT30 connector Recommend to use 2s 350mah/400mah/450mah/520mah battery Compatible with Insta360 Go Camera
MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.HEX Default protocol: DSHOT600
Onboard Frsky SPI D8 receiver Version
SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 modelChannels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m
Onboard Flysky SPI receiver Version
SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 200~300m Failsafe support
Onboard DSM2/X SPI receiver Version
SPI BUS receiver DSM2/DSMX compatible Channels: Max 12ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 200m~300m RSSI enable(show on the goggles)
External Frsky R-XSR receiver version
Weight: 1.5g Number of channels: 16CH (1-16CH from SBUS channel, 1~8CH from CPPM channel) Operating Voltage Range: 3.5V~10V Operating Current:70mA@5V Firmware Upgradable Compatibility: FrSky X Series modules and radios in D16 mode Could support Frsky New ACCESS Protocol ( Upgrade firmware)
External TBS CRSF Nano receiver version
Original TBS CROSSFIRE Receiver ,CRSF Protocol , Official TBS transmitter compatible
Image Sensor: 1/3″ CMOS Sensor Horizontal Resolution: 1200 TVL TV System: NTSC or PAL IMAGE: 4:3 Synchronization: Internal Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000 S/N Ratio : >52dB (AGC OFF) Video Output: CVBSLens: 1.8mm Min. Illumination: 0.001Lux@F1.2 Auto Gain Control: YES BLC: YES WDR: Global WDR DNR: 3D DNR Dimensions: 14*14mm(with bracket to 19*19mm) Wide Power Input: DC 3.7-18V Work Temperature: -20℃~+60℃ Weight: 2g (N.W.)
Great little thing that is responsive and fun to fly, not super hard for beginners and super nimble for experienced flyers too!
L
Logan
Great quad
I got this thing to reenter the fpv quad world. I've been really enjoying the flights. It's fast on 2S but not out of control. Highly recommend.
K
Kin Lam
capable little 1s,
indoor and outdoor, both capable.
J
Jazz
ESC died after 10 flights
The drone flies great and is very efficient (7 minutes of freestyle on a 450 2s). The electronics are quite exposed so I recommend not flying it in wet conditions or conformal coating. They really should provide some mechanism to hold the antennas in place without getting chopped up by the propeller. I got the FrSky SPI receiver and the range is quite bad, it will fall out of the sky with no warning at random when flying just 60 feet away line of sight with no obstructions. Highly recommend getting a dedicated receiver and orienting the antennas appropriately. Unfortunately one of the ESCs died after 10 flights - I did not turtle mode or block the props in anyway. Got a replacement AIO controller board for $50 to give it another shot. I choose this option so I would not have to solder/assemble but I now have to solder on a receiver and repair the drone so I can't say its a durable drone and ended up costing me as much as a higher quality, more durable quad like a diatone or iFlight which I should have gotten instead.
Nice and roomy. Can fit my HDO2s with a HDZero or Walksnail VRX attached. Has an outside pouch for cords and additional antennas. And the lining feels so nice and soft.
