• 
• 
• 
• 
• 
• 
• 
• 

The pilot & videographer Ellisvanjason and iFlight teamed up to craft a cinematic 6 inch drone that ensures agility and flight time and therefore combines the advantages of both 5 inch and 7 inch drones.

Features:

- 6 inch drone re-engineered: This drone was specifically designed for 6 inch

- H-shaped frame with robust middle section for less props in view while remaining stiffness

- XT60 front-mount: Compare to other drones the mount sits in the front and gives more space on the back.

- Built in BEC to directly power a gopro (no battery needed)

- Hybrid motor design: This motor is optimized for 6 inch.  Can be used with bi- blades (efficiency) and tri-blades (agility & trust). 

- Antenna mount: Solid antenna mount for less ocillations when using long antennas

- Long back bone: Enough space up to 3000mAh 6S batteries

- Gladiator shell: Protection shell from dust and water droplets (shall be removed for max. flight time)

- GPS: A high-end GPS is used to minimize the risk of failure during proximity flights 

- ESC: The drone consists iFlight's new ESCs with built-in spike absober for more reliability

- 9min flight time with 1800mAh 6S

- 9+ with 3000mAh 6S Lipo or 4000mAh 6S Li-Ion

- Get Ellisvanjason's tune on ellisvanjason.com

Specifications:

- Upper(middle) plate thickness: 2.5mm

- Bottom plate thickness: 1.5mm 

- Total Dimensions: 254*254mm 

- Bottom to top distance: 22mm 

- Geometry: H-shaped frame

- Top plate thickness: 2mm 

- Ellisvanjason 2506 motors 

- Gemfan 6032 propellers

- Arm Thickness: 6mm

ELECTRONICS // BLITZ F7 Stack (F7 V1.1 + 55A 4in1 ESC)：

FC //BLITZ F722 Flight Controller

• Mount pattern: 30.5*30.5mm / 4mm PCB hole diameter
• Smartaudio / IRC Tramp VTX protocol supported
• Firmware target: IFLIGHT_BLITZ_F722
• Motor outputs: 4x (SH1.0 connector)
• Flash: 32MB (Blackbox flash)
• I2C serial: SDA / SLA pads
• Dimensions: 36.5*35 mm
• Barometer: DPS310
• OSD Chip: AT7456E
• LED controller: Yes
• MCU: STM32 F722
• Beeper pad: Yes
• Gyro: BMI270
• Weight: 7.8g
• UARTS: 6

ESC // BLITZ E55 4-IN-1 2-6S 55A ESC

• Supports: DShot DShot150/300/600/MultiShot/ OneShot etc.
  
• Mounting Holes: 30.5*30.5mm/Φ4mm
  
• Target:   IFLIGHT_BLITZ_G2
  
• Supports 2-6S Lipo input
  
• Current sensor: Yes
  
• Constant: 55 Amps 
  
• Current rate: 200
  
• Burst: 65 Amps
  
• Weight: 15.3g
  
• MCU： G071
  
• BEC: No

BOB57 HD Included Components and Parts

• 2 x GEMFAN 6032- CW propeller + 2 x  6032 CCW (Green)
• 2 x GEMFAN 6032- CW propeller + 2 x  6032 CCW (Black)
• 1 x Albatross LHCP 5.8GHz SMA FPV Antenna 150mm
• 1 x Albatross LHCP 5.8GHz SMA FPV Antenna 60mm
• 1 x USB Type-C 5V Balance Plug Power Cable 55mm
  
• 2 x iFlight Lipo Strap 20*250mm (Black)
• 1 x Nebula Pro Vista HD System
• 1 x Pre-built and Tested BOB57