The old days are over, getting your electronics full of dirt and wet grass every time you crash. Our latest frame reduces contamination that could build up on your flight controller or ESCs, preventing failure or short circuits. Strategic airflow to keep your components cool and clean without taking any shortcuts in weight or performance. Illuminated side panels and 360-degree TPU protective parts.
Highlights
V1 to V2 was upgraded for the DJI O3 HD Air Unit Digital Transmission
Specially Designed Heatsink for DJI O3 Air Unit
New Camera Mount for a wider camera FOV with TPU damping inserts
New Side Panels to perfectly fit the O3 Air Unit in the back
New Dual 5.8G VTX Antenna TPU mount
Latest Nazgul Frame Upgrades for Maximum Protection
Optional Parts to select (not included in frame kit):
New Anti Spark Filter to prevent rapid voltage and current spikes plugging in a battery
Single DJI VTX Antenna TPU to install the original DJI O3 set included antenna.
Upgrading your Nazgul F6 V1?
If you want to upgrade your Nazgul Evoque F6 V1 with the DJI O3 Air Unit read this:
- The FC (Flight Controller) to O3 VTX connector is different than the older Caddx Vista/Polar plug. You'll need to DIY.
- The RX (Receiver) position changed. V1 antenna length is 75mm, V2 is 220mm. You'll need to DIY.
- The XT60 plug was changed, you'll need to de-solder the V1 plug and install the V2 plug. Included in the frame kit.
- If you're going from F6X V1 to F6X V2 all motor wires will have the same length.
- If you're going from F6X V1 to F6D V2 the back motor wires need to be extended, since you change frame geometry.
- The Antenna TPU in the back comes in 2 Versions; One for the original single DJI VTX antenna, or one for the dual antenna setup. The kit includes a dual antenna TPU. 2x 5.8G LHCP antennas need to be installed.
- The Nazgul Evoque F6 V2 BNF comes with a new Anti Spark filter pre-installed. Please select the option to purchase separately; it's not included in the frame kit.
Changelog
December 13, 2022: New silicone inserts have been designed to replace the TPU ones，which are holding the 03 cam in the side panels.
Specifications
Product Name: Evoque F6 V2 Frame Kit
Frame wheelbase: 255mm (Squashed X) / 262 mm (DeadCat)
Frame Dimension: L196*W164*H36 mm (Squashed X) / L209*W162*H36 mm (DeadCat)
Right away, this is the best 65mm Whoop I know. Not even close.
I ordered two, one is more or less stock, just the PEEK motor screws and V3 cockroach. The second is upgraded to 0702 27000kV but will go back because I like the 25000kV more because of smoother throttle response and perfect betaflight tune.
Now the but:
1. On both quads I had to replace the BeeEye for a spare one because both are out of focus.
2. the yellow props were way too loose and very brittle. I lost two on my maiden. Black, blue and red are very tight (too tight for such a fragile prop) but if you get them on without bending them, they will last.
3. why does the quad not come with the lighter frame right away?
4. PH2.0…. You know the drill.
On that price point, even after the frame and PEEK upgrade I can forgive these quality issues. Especially considering the great tune and quality FC and motors. But be sure to order a replacement cam and props right away.
This was kind of a late night lark. I'd seen this upgrade for the Mk3 for a while and pondered whether it was a gimmick or not, and I'm pleased to say it's a genuinely good upgrade. It has reduced the noise of my Mk3 considerably. I haven't noted any significant increase in print quality, but the old drone of the bed is gone and that's completely worth it.
