• Description

Using a dual gyro setup in 90° phase and a F7 processor will have your quad dialed in to the max!


Specs

  1. MCU: STM32F722RET6 216MHz
  2. 2x ICM20602 GYROS 90 deg phase
  3. Built in Betaflight OSD
  4. Up to 8S (36V) direct battery power
  5. Buzzer pads for external buzzer
  6. Built in voltage monitoring resistor
  7. 5V 2A BEC
  8. Dedicated LDO for Gyro, noise free gyro power
  9. Dedicated LDO for OSD, cleaner OSD signal
  10. Led strip shares 5V with 5V/2A BEC
  11. 6 UARTS: UART1, UART2, UART3, UART4, UART5, UART6
  12. Built in camera control pin with resistor and capacitor
  13. 5 Full UARTS with RX AND TX pins
  14. Logical pin layout for cleanest build possible
  15. 8 pin 4 IN 1 ESC plug
  16. Remapable LED pad for additional motor output
  17. TX3, RX3 can be used for I2C for external compass
  18. 5V, VBAT selectable VTX and CAM power
  19. 16M Blackbox flash chip
  20. No flicker VTX pit mode switch (positive switch)
  21. M4 Can be selected either led strip signal or M4 signal for RPM filtering

20 X 20 mounting hole with true 25mm board dimensions


Official Betaflight Target: TalonF7Fusion

Please use user1 for Pit Switch Mode Switch


For the Legacy Clracingf7 target you will need to do the following:

To get Motor 4 to work please use the CLI command below using Betaflight V4.0.4. A custom hex is coming soon for 4.0.4.

Resource MOTOR 6 None

Resource MOTOR 4 C08

Save


To get 5V to your VTX please go to the mode tab in Betaflight and setup a mode switch for vtx pit


Setting up Pit Mode:


Top Layout:


Bottom Layout:

Description

Using a dual gyro setup in 90° phase and a F7 processor will have your quad dialed in to the max!


Specs

  1. MCU: STM32F722RET6 216MHz
  2. 2x ICM20602 GYROS 90 deg phase
  3. Built in Betaflight OSD
  4. Up to 8S (36V) direct battery power
  5. Buzzer pads for external buzzer
  6. Built in voltage monitoring resistor
  7. 5V 2A BEC
  8. Dedicated LDO for Gyro, noise free gyro power
  9. Dedicated LDO for OSD, cleaner OSD signal
  10. Led strip shares 5V with 5V/2A BEC
  11. 6 UARTS: UART1, UART2, UART3, UART4, UART5, UART6
  12. Built in camera control pin with resistor and capacitor
  13. 5 Full UARTS with RX AND TX pins
  14. Logical pin layout for cleanest build possible
  15. 8 pin 4 IN 1 ESC plug
  16. Remapable LED pad for additional motor output
  17. TX3, RX3 can be used for I2C for external compass
  18. 5V, VBAT selectable VTX and CAM power
  19. 16M Blackbox flash chip
  20. No flicker VTX pit mode switch (positive switch)
  21. M4 Can be selected either led strip signal or M4 signal for RPM filtering

20 X 20 mounting hole with true 25mm board dimensions


Official Betaflight Target: TalonF7Fusion

Please use user1 for Pit Switch Mode Switch


For the Legacy Clracingf7 target you will need to do the following:

To get Motor 4 to work please use the CLI command below using Betaflight V4.0.4. A custom hex is coming soon for 4.0.4.

Resource MOTOR 6 None

Resource MOTOR 4 C08

Save


To get 5V to your VTX please go to the mode tab in Betaflight and setup a mode switch for vtx pit


Setting up Pit Mode:


Top Layout:


Bottom Layout: