建構影片:

具有優質零件和功能的高階控制器
採用 F7 處理器和 45Amp BLheli32,採用 NewBeeDrone Smoov 認證的硬體設計,支援多達 3-6S 電池,為自由式或賽車提供最佳、可靠的品質和性能。

專為支援 DJI 天空端而設計。
雖然 DJI 天空端最多只能支援 4S,但 Cricket200 Stack 可以透過為 DJI 天空端提供 9V 16W 的清潔電源,使 DJI 天空端相容於 6S 電池。

即插即用。無需焊接細電線。
Cricket200 Stack 包括一束用於連接飛控和 ESC 的電線以及用於連接飛控和 DJI 天空端的電線。

*僅適用於完整的 DJI 系統。如果使用Crossfire,仍然需要焊接。

Cricket200 飛行控制器 F7 規格:

  • MPU6000陀螺儀
  • STM32F722 216MHz
  • 9V 2A 18W DJI FPV 天空端設計
  • 5V相機電源
  • BetaFlight OSD
  • 31.5x27 CB,附20x20安裝孔,重量:5.85g
  • 6 個UART。 UART1(SBUS 逆變器)
  • UART2(免費)
  • UART3(反向遙測)
  • UART4(免費)
  • UART5(智慧音訊)
  • UART6(免費)
  • 內建4合1電調插座(含電調遙測、外接電流感測器) JST1.0 8Pin
  • 與 NBD Infinity200 電調即插即用。也相容於市面上大部分ESC。
  • 內建焊盤,用於 ESC 訊號輸出和電源
  • 板上印有版面說明 - 無須說明!
  • DJI FPV 天空端插座(使用UART1和UART6)



Cricket200 電調規格:

  • 鋰聚合物電源輸入:3S-6S
  • 電調編程:BLHeli32
  • 連續電流:45Ax4
  • 突發電流:55Ax4
  • 重量/尺寸:13.0g / 39x29.5x8mm
  • 安裝孔:20x20mm
  • 訊號插頭 JST1.0 8pin 插頭 附 NBD Infinity200FC
  • 焊盤準備好訊號和電源。
  • 散熱片設計
  • 2Oz 銅 8 層 PCB
  • 由 NBD 團隊設計的 Smoov 效能

包括:

  • 1x Cricket 200 4合1電調 BLHeli32 45A
  • 1x Cricket 200飛行控制器 F7
  • 8x 短索環 8x 長索環
  • 5x 鋼螺絲 25mm
  • 13x 尼龍螺母
  • 470uf 35v 電解電容
  • 1x Cricket200 FC 至 Cricket200 ESC 電纜 30 毫米
  • 1x Cricket200 FC 至 Cricket200 ESC 電纜 50 毫米
  • 1x Cricket200 FC 至 Cricket200 ESC 電纜 85 毫米
  • 1x Cricket200 FC 轉 DJI Air 模組電纜 70 毫米

官方 Betaflight GUI 上的韌體目標名稱:NBD_CRICKETF7



Customer Reviews

Based on 15 reviews
80%
(12)
0%
(0)
13%
(2)
0%
(0)
7%
(1)
J
Jason lee
Absolute garbage

This is the second time that newbeedrone has gotten me for a stack and it'll be the last. I'm not going to bother with an RMA either. 7 weeks of emails and they sent me back the same garbage last time Superbad customer service.

V
Vladimir Bueno
NewBeeDrone Cricket200 Stack (ESC+FC)

completely satisfied with this product

j
javier magdaleno
Super !!

Thanks for the fast shipping

S
StockBad
Beyond good!

Very nice combo, easy as cake to setup and smooth as skippy to fly.

E
ExplodingEvo
F7 stack that works, but lacking features for the price point.

I had an issue with both an ESC and FC from 2 different stacks I got, but NBD took care of me quickly. These are great for DJI builds because of plug and play but there are 3 things I'd change on this stack.
1. It needs a plug for the receiver IMO. If I don't have to solder the air unit then I don't want to solder a 3rd party receiver. Lose the 3rd ground on the plug give me RX1/TX1/G/5V that I can break out for expressLRS. or give me a second plug that I can use so I can avoid soldering on the FC altogether.
2. Give me some blackbox memory. This is the first time in a long time I bought an F7 flight controller with no blackbox memory. at least 8MB so it's easier for me to tune!
I have 2 of these stacks, so I'll be using them for a while. But part of me wishes I got the xrotor 20x20 stack instead.

相關產品

看更多
DJI Neo 組合
DJI Neo 組合
DJI
$ 289.00
大疆 Neo
大疆 Neo
DJI
$ 199.00
跑攝夜鷹3 V2
$ 69.99