DON'T LET YOUR PACKS GRIP SLIP!! Make sure that your lipo battery is one with your craft my applying Lipo-Lock to your frame and battery.
A simple solution that doesn't matter if you get it dirty and will not lose its effectiveness over a short amount of time.
Oh yeah, did we mention that you can also fly a bottom mount battery without a strap?! Even though we do not suggest that technique, it is good to know that your flight is not just dependent on 1 or 2 straps.
Includes 4x 2'' pieces of 3M Extreme Dual lock tape
Instructions:
Add 1 piece of LiPo-Lock to the craft and 1 for each battery you plan to use with the craft.
We usually fit to size, cut if needed and then apply with pressure for several minutes. We use the 2'' strips for 4-6s and cut it down depending to size of the craft / battery for everything smaller. Apply with more force and time the smaller you go for the best bond.
Make sure the first application is done well with a good grip on the carbon and it will be nice and secure!
Note:
This is an extreme version of Dual Lock that has to be normally special ordered in a large roll. This item is meant to make it easily available for pilots to try and secure their packs to their crafts without buying a huge roll!
These lock lipos were n tight! Sweet part is, they don’t get gummed up with garbage like big lot store velcro. Highly recommend!
F
Fpv Budget Builds
Great stuff
Tape works good. Battery stays in place. Putting it on all my quads that use a strap system for battery.
N
Nathan C
Good piece of mind
Holds on tight! Good for holding down batteries. Also handy for holding down a VTX in combination with a ziptie.
S
Saverio Avella
Great Security for Your Lipos
These are great to use on all your quads/batteries.
They really secure your batteries to your quad. Definitely better than those sticky pads.
The only disadvantage using this system is that it’s best to use it on all your quads because you would not want to remove the tape from your batteries to use it on quads that do not have the lock tape.
Right away, this is the best 65mm Whoop I know. Not even close.
I ordered two, one is more or less stock, just the PEEK motor screws and V3 cockroach. The second is upgraded to 0702 27000kV but will go back because I like the 25000kV more because of smoother throttle response and perfect betaflight tune.
Now the but:
1. On both quads I had to replace the BeeEye for a spare one because both are out of focus.
2. the yellow props were way too loose and very brittle. I lost two on my maiden. Black, blue and red are very tight (too tight for such a fragile prop) but if you get them on without bending them, they will last.
3. why does the quad not come with the lighter frame right away?
4. PH2.0…. You know the drill.
On that price point, even after the frame and PEEK upgrade I can forgive these quality issues. Especially considering the great tune and quality FC and motors. But be sure to order a replacement cam and props right away.
This was kind of a late night lark. I'd seen this upgrade for the Mk3 for a while and pondered whether it was a gimmick or not, and I'm pleased to say it's a genuinely good upgrade. It has reduced the noise of my Mk3 considerably. I haven't noted any significant increase in print quality, but the old drone of the bed is gone and that's completely worth it.
![[pre-order]BetaFPV A03 400mW 5.8G VTX](http://newbeedrone.com/cdn/shop/files/8c6db81bad1f7fab20f937b5a3deb50b_720x_2e752615-4a65-4c95-a2d8-df964bdc15b6_{width}x.webp?v=1700635982)
![[pre-order]BetaFPV Aquila16 FPV Kit](http://newbeedrone.com/cdn/shop/files/2_720x_f35023be-a70b-48e4-97c5-277987d855e7_{width}x.webp?v=1700619059)
![[pre-order]BetaFPV Moxon Radio Transmitter Antenna V2 (1pcs)](http://newbeedrone.com/cdn/shop/files/MOXON2.4_720x_aa23e915-1266-4875-bf6e-91bd353c6047_{width}x.webp?v=1700537807)
