HolyBro

HolyBro SiK Telemetry Radio - Long Range

$211.99
$211.99
Sale

Overview

The Holybro SiK telemetry radio is a small, light, and inexpensive open-source radio platform that typically allows ranges of better than 300m out of the box. With a patch antenna on the ground, the range can be extended to several kilometres. This plug-and-play telemetry radio is ready for Pixhawk Standard and other flight controllers, making it an easy way to set up a telemetry connection between your flight controller and a ground station. It uses open-source firmware designed to work well with MAVLink packets and to integrate with Mission Planner, ArduPilot, QGroundControl, and PX4.

Features

  • Open-source SiK firmware
  • Plug-and-play for Pixhawk Standard flight controllers
  • An easy way to connect your flight controller and ground station
  • Interchangeable air and ground radio
  • Micro-USB port (Type-C adapter cable included)
  • 6-position JST-GH connector

Specifications


 SiK Telemetry Radio 100mW SiK Telemetry Radio 500mW SiK Telemetry Radio 1W
Max RF Power 20 dBm 27 dBm 30 dBm
Receive sensitivity -121 dbm @2kbps RF Data Rate, -105 dbm @64kbps RF Data Rate
Antenna Gain 2dBi 5dBi
RF Data Rates 2, 4, 8, 16, 32, 64(default), 96, 128, 192, 250 kbps
Serial Interface Data Rate 1.2, 2.4, 4.8, 9.6, 19.2, 38.4, 57.6(default), 115.2 kbps
Frequency Band 902MHz - 928MHz or 414MHz - 460MHz
Interference Immunity Frequency Hopping Spread Spectrum (FHSS) Configurable duty cycle
Address Options Network ID: 0 –255
Channels Up to 50 Frequency Hopping Channels
Supported Network Topologies Point-to-point
Configuration Method MissionPlanner or AT Commands
Data Framing Standard or MAVLink protocol framing
Error correction Corrects up to 25% of bit errors with open-source SiK firmware
Serial Data Connector & Interface 6-pin JST-GH connector, 3.3V-TTL
USB Micro-USB Type-C
SMA Connector RP-SMA female
Power Connector NA XT30
Operating Temperature -40~85°C
Dimension 28 x 53 x 10.7mm (without antenna) 66.5 x 32 x 16.5mm (without antenna)
Weight 23.5g w/ antenna 67g w/ antenna
Input Voltage (DC) 5V 7~28V
  • 2-way full-duplex communication through adaptive TDM UART interface
  • Transparent serial link
  • MAVLink protocol framing
  • Built-in FT230X/FT23 USB to BASIC UART conversion IC

Electrical Data

  • Supply voltage:
    • 100mW and 500mW version: 5V DC (from USB or JST-GH)
    • 1W version: 7~28V DC via XT30
    •  
  • Transmit current: 100 mA at 20 dBm
  • Receive current: 25 mA
  • Serial interface: 3.3 V UART

FCC Identifier

Package Included

  • 100mW and 500mW options
    • Radio modules with antennas *2
    • Micro-USB to USB-A cable *1
    • Micro-USB to Micro-USB OTG adapter cable *1
    • Micro-USB to Type-C adapter
    • JST-GH-6P to JST-GH-6P cable *1 (for Pixhawk Standard FC)
    • JST-GH-6P to Molex DF13 6P (for Pix32, Pixhawk 2.
    • 4.6, etc.)
  • Single 1W
    • 1W radio module with antenna *1
    • High-gain omnidirectional antenna *1
    • Male Type-C to male Type-C USB cable *1
    • Male XT30 to female XT30 adapter cable *1
    • Male XT30 to female XT60 adapter cable *1
    • JST-GH-6P to JST-GH-6P cable *1 (for Pixhawk Standard FC)
    • Rubber damping grommet *3
    •  
  • Dual 1W
    • 1W radio modules with antennas *2
    • High-gain omnidirectional antennas *2
    • Male Type-C to male Type-C USB cable *1
    • Male XT30 to female XT30 adapter cable *1
    • Male XT30 to female XT60 adapter cable *1
    • JST-GH-6P to JST-GH-6P cable *1 (for Pixhawk Standard FC)
    • Rubber damping grommet *3

Manual

Telemetry-Radio-V3-Quick-Start-Guide

Some Tips

https://ardupilot.org/copter/docs/common-configuring-a-telemetry-radio-using-mission-planner.html