NEO 3 uses a hardware design similar to NEO V2, and upgrades the GNSS navigation module to the M9N module that supports the four mainstream satellite systems of Beidou, GPS, Galileo and Glonass. The positioning accuracy has been significantly improved. It is a high Cost-effective unmanned system positioning and navigation module. It integrates compass, barometer, flight controller status light, buzzer, and safety switch in one; it has the characteristics of high sensitivity and strong anti-interference.
Features
Buzzer prompt
safety switch
CAN Bus
MS5611 Barometer
RGB Status Light
CROCOMM custom four-star high gain antenna
Ublox M9N Satellite receiver
New generation satellite receiver Ublox M9N，The actual measurement can reach a maximum accuracy of 0.7m.
Simultaneous reception by the four satellite systems
Supports simultaneous reception of Beidou, Galileo, Glonas, and GPS four satellite systems
RM3100 industrial sensor
Using RM3100 industrial grade sensor, has better anti-interference performance
Triple filter design
NEO 3 Pro adopts SAW+LNA+SAW triple filter design, effectively avoiding the influence of remote control, data transmission, 4G signal on GPS positioning reception
Weight
0.5 kg
Dimensions
10 × 10 × 5 cm
NEO 3 Specifications
Processor
-
Compass
IST8310
GNSS receiver
UBLOX NEO M9N
RGB drive
NC5623C
Buzzer
Passive buzzer
Safety switch
Physical button
GNSS
Beidou、Galileo、 GLONASS、 GPS
GNSS Augmentation System
SBAS:WAAS,EGNOS,MSAS QZSS:L1s(SAIF) other：RTCM3.3
Number of concurrent GNSS
4
Frequency band
GPS:L1C/A GLONASS:L10F Beidou:B1I Galileo:E1B/C
Horizontal accuracy
2.0M
Speed accuracy
0.05M/S
Nav. update rate
25Hz(Max)
Acquisition
Cold start：24S Hot start：2S Aided start:2s
Number of satellites(MAX)
32+
Sensitivity
Tracking and nav-167dBm Cold start Hot star-148dBm Reacquisition -160dBm
Protocol
UART+IO+I2C
Port TYpe
GHR-10V-S
Supported flight controller
CUAV series, Pixahwk series
Wave filtering
SAW+LNA+SAW
Anti-Electromagnetic/radio frequency interference
EMI+RFI
Upgrade firmware
support
Support Flight control type
Ardupilot/PX4*(PX4 is still working hard to adapt to the clock)
Input voltage
5V
Operating temperature
-10~70℃
Size
60*60*16MM
Weight
33g
NEO 3 level accuracy when the SBAS enhancement system is turned on, the nominal accuracy is 1.5m (default); when the SBAS enhancement system is turned off, it is 2.0m
NEO 3 supports RTCM3.3 injection, but does not support RTCM output; it can achieve pseudorange differential (meter-level positioning) but does not support carrier phase differential (RTK), and it needs a base station that supports RTCM3.3 output.
When you connect NEO 3 to autopilots of other brands (non-CUAV autopilots), the buzzer will not work. If you need to use it on autopilots of other brands, please selectNEO 3 Pro.
Autopilot parameter settings
Neo 3 is a plug-and-play module without parameter settings.
I really like this radio but I had a gimbal stick pull out without any pulling on it. I've had this happen with other name brand radios so it's not a surprise or let down. A little super glue and right back at it. It feels great! I love the full sized gimbals! I have the zorro and the boxer but I think this one is the right fit for me.
Handy as a second transmitter for travel, tiny whoops, etc
Surprisingly good for the price especially with ELRS. It has just enough switches that I can do most of what I can with the TX16S, and it's so much easier to throw in a bag and go. My only wish is that I could put the thumb-grippies style of stick ends on it easily (and still remove them for storage), but maybe someone will come up with an adapter or similar. Next step is to try a Gemini ELRS nano module and see what kind of range is possible on that.
