TheDJI Avata Fly More Kitfeatures two DJI Avata Intelligent Flight Batteries and a 4 Capacity Battery Charging Hub. Bring more power on the go with this battery kit!
Features
Two DJI Avata Intelligent Flight Batteries for longer flight days
Battery Charging Hub charges up to 4 batteries in sequence
DJI AVATA INTELLIGENT FLIGHT BATTERIES
The Intelligent Flight Battery has a rated capacity of 35.71 Wh and a powerful battery life of approximately 18 minutes. With a built-in DJI Intelligent Battery Management System, battery status is monitored and reported in real-time, allowing you to focus less on power levels and more on flying.
DJI AVATA BATTERY CHARGING HUB
The DJI Avata Battery Charging Hub can charge four batteries in sequence, which greatly enhances the charging efficiency.
Specifications
DJI AVATA INTELLIGENT FLIGHT BATTERIES
Charging Temperature Range: 5° to 40° C (41° to 104° F)
Chemical System: LiNiMnCoO2
Charging Voltage Limit: 17 V
Battery Capacity: 2420 mAh
Discharge Rate: Typical: 7C
Energy: 35.71 Wh@0.5C
Weight: Approx. 162 g
Voltage: 14.76 V
Type: Li-ion
DJI AVATA BATTERY CHARGING HUB
Operating Temperature Range: 5° to 40° C (41° to 104° F)
Right away, this is the best 65mm Whoop I know. Not even close.
I ordered two, one is more or less stock, just the PEEK motor screws and V3 cockroach. The second is upgraded to 0702 27000kV but will go back because I like the 25000kV more because of smoother throttle response and perfect betaflight tune.
Now the but:
1. On both quads I had to replace the BeeEye for a spare one because both are out of focus.
2. the yellow props were way too loose and very brittle. I lost two on my maiden. Black, blue and red are very tight (too tight for such a fragile prop) but if you get them on without bending them, they will last.
3. why does the quad not come with the lighter frame right away?
4. PH2.0…. You know the drill.
On that price point, even after the frame and PEEK upgrade I can forgive these quality issues. Especially considering the great tune and quality FC and motors. But be sure to order a replacement cam and props right away.
This was kind of a late night lark. I'd seen this upgrade for the Mk3 for a while and pondered whether it was a gimmick or not, and I'm pleased to say it's a genuinely good upgrade. It has reduced the noise of my Mk3 considerably. I haven't noted any significant increase in print quality, but the old drone of the bed is gone and that's completely worth it.
![[pre-order]BetaFPV A03 400mW 5.8G VTX](http://newbeedrone.com/cdn/shop/files/8c6db81bad1f7fab20f937b5a3deb50b_720x_2e752615-4a65-4c95-a2d8-df964bdc15b6_{width}x.webp?v=1700635982)
![[pre-order]BetaFPV Aquila16 FPV Kit](http://newbeedrone.com/cdn/shop/files/2_720x_f35023be-a70b-48e4-97c5-277987d855e7_{width}x.webp?v=1700619059)
![[pre-order]BetaFPV Moxon Radio Transmitter Antenna V2 (1pcs)](http://newbeedrone.com/cdn/shop/files/MOXON2.4_720x_aa23e915-1266-4875-bf6e-91bd353c6047_{width}x.webp?v=1700537807)
