NeutronRC AT32F435 mini AIO, 32 Bit AM32 ESC,Board Flight Controller with 25.5*25.5mm Mounting pattern for FPV drone
AboutATBETAFLIGHT, it is a special branch of BETAFLIGHT, which is different from the MCU master control using non-ST chips, has a lower price, and a complete BMI270 driver, allowing it to calibrate the gyroscope at startup and have better flight stability .
Currently, the QUICKSILVERfirmware has been perfectly supported, and it performs perfectly on a small frame with a protective frame
1. How to connect BETAFLIGHT CONFIG software and the difference with BF;
1.2, betaflight 10.9 Configurator Opens the following setting options
2. About the AM32 ESC, there is a known bug in the AM32 version of the website, which causes malfunctions after writing or modifying the ESC. We have submitted a PR to fix this issue. Currently, you can use the development version web configurator to modify the AM32 ESC configuration
About Betaflight's support for artery MCU:
The current BF 4.4.X version does not support the AT32F435 chip. Our default firmware is based on the 4.3.2 branch. At present, it is seen in the BETAFLIGHT code base that BF4.5 will soon support the AT32F435 chip, and the specific progress is uncertain.
How to update FC and ESC firmware, please refer to the download document
The default FC Flash ATbetaflight 4.3.2-RC4 firmware, ESC flash HF32 firmware, usually, you do not need flash FC and ESC firmware, just install and set related options according to your settings. HF32 ESC Configurator
So far, extremely happy with it. I would probably give this one a six out of 5 stars with the ease of setting it up and putting it in my drone and flying it. The only problem is is I have it in a foxwhoop 35 and not a 3-in race drone so I don't know the true durability of this all in one. But, from what I've experienced so far I would be more than willing to buy this board as a replacement for any of the all-in-ones that I have on any of my droI would probably give this one a six out of 5 stars with the ease of setting it up and putting it in my drone and flying it. The only problem is is I have it in a fox whoop 35 and not a 3-in race drone so I don't know the true durability of this all in one. But, from what I've experienced so far I would be more than willing to buy this board AGAIN as a replacement for any of the all-in-ones that I have on any of my drones (that requires a AIO)
This 4 cell LiHv is great for flying slow and for long flight times on my 6 cell drone. Even though it's not the correct cell count, the LiHv 4.35 max voltage brings it closer into range.
I am kinda new to fpv drone flying but not new to RC and this radio is by far the best I’ve used. Definitely complicated and has a lot to lean but its loaded with features and is fully customizable and way more advanced then anything Ive used before. Coming from the Spektrum platform YouTube is your friend as there is a lot to learn.
had a few issues i used they ROBO 1002 and it fit fine without they carbon. but needs they carbon to hold battery had to use a mix of screws, had issues with props rubbing they frame with carbon using AZI props solved by not pressing props all the way down. I ordered they black and yellow, Black has a better mount for they antenna to keep in place !! yellow needs something to tie down
this gift would be nicer with a genuine properly welded whoop
Hello Franz,Thank you for the information provided. Do you have a hot air soldering station? You can use it to heat the capacitor, which should allow you to reseat it into position. After that, test to see if it's functioning properly within Betaflight. If everything is working correctly, you can further secure the capacitor with non-conductive adhesive.We sincerely apologize for the inconvenience caused. We have also credited your account with $10, which you can use to purchase any products from our store. If you have any questions or need further assistance, please feel free to reach out to us. We are always here to help. Thank you, NewBeeDrone Support