HAKRC F411 20A 一體機

特徵:

1.PCB採用高階8層2oZ厚銅,過流能力更強,散熱好。

2.MOS採用進口30V大耐流MOS,壽命長,負載能力強。

3.採用工業級LDO,耐高溫。

4.採用優質日本村田電容,濾波性能強

 

規格:

品牌:HAKRC

產品名稱: HAKRC F411 20A 一體機

安裝孔:25.5*25.5mm/26.5*26.5mm

重量:8.5公克

包裝重量:50g

尺寸:31*31mm

 

飛行控制器:

CPU:STM32F411CEU6

慣性測量單元:ICM42688

螢幕顯示:AT7456E

晴雨表:SPL06

LED:支援可編程,如WS2812

電流表:有

韌體:HAKRC F411D

支援接收機:Frsky/ Futabas/ Flysky/ TBS Crossfire/ DSMX:DSM2

 

ESC鍵:

韌體:BLHELI_S (G-H-20)

支援PWM、Oneshot125、Oneshot42、Multishot、Dshot150,Dshot300,Dshot600

輸入:2S-5S 鋰電池

騙局。電流:20A

峰值電流:25A

 

套餐包括:

1x F4126 一體機

4x M2 避震器

1 條 XT30 電源線

1x小繃帶

1 個 C 型 USB

1 條 USB 線

1x 270uf/35V 電容器

1x DJI FPV 線

1x DJI O3 天空端三合一連接線

1x 說明

Customer Reviews

Based on 3 reviews
67%
(2)
0%
(0)
33%
(1)
0%
(0)
0%
(0)
H
Hansen Tsang
Good and inexpensive

Works well so far. I have two of them and I am still trying to figure out if it works well with BetaFlight V4.5. It is working well with V4.4.3 though. CPU loading seems to be much higher with V4.5

T
Tyrone Lawson
Good bang for the buck

My new favorite FC. You have the pinout in the box and I haven't had any issues with it so far. I am currently using 4 of them.

D
Duncan Stewart
Good AIO, I made a mistake and burned out another one i guess?

I purchased two, put Conformal Coating onto these board before soldering the pads, mind you I put one small layer near the pads then proceeded to put two more layers on the rest of the boards knowing I will be back to put more on.

I got a Cold Solder Joint on the Negative Terminal, I tried to solder it back on, kept on popping off, I proceeded to put more solder on and it seemed to be stuck, then I tested the FC and it wasn’t working.

So it’s Toast, I tested the USB, toast. So I was able to get my second one to solder “welded” I’ve been flying that for a week, did the same process, but went back and tried to clean more of the Conformal Coating off with IsoPropyl.

I damaged it within a week of owning it, contacted NewbeeDrone and they push it along to HAKRC. I’ve been talking to them for a week, they asked the same questions over and over, I had to repeat myself to them, send tons of photos, while they lectured me on the “three defense” sequence of conformal coating.
Yeah I didn’t tin up the pads first, but the amount of Conformal Coating I put on shouldn’t have caused it not to make a good enough contact?

So I was talking to their “support” email and I just realized it’s not worth it to RMS the board especially since they kept on being vague with their answers.

I got a bunch of their boards, but I do have the most problem with Conformal Coating and their boards and me burning them out when I build or transfer.

What a bummer.