Too difficult to access the USB port on your compact 2-4" quad? Say goodbye!
It's time to say goodbye to this trouble! With this Bluetooth stack, you don't need to connect your quad to the PC for FC and even ESC tuning, everything can be done wirelessly in the SpeedyBee app.
Tune Flight controller and ESC wirelessly!
Power the quad, connect the SpeedyBee app via Bluetooth, configure the UART Ports,PID,OSD and every other settings on this flight controller.Also, every parameter of the BLHeli_S ESC in this stack can be set via the app.
Change motor directions wirelessly!
With this stack, when you finish your build, connect to the SpeedyBee app, change the motor directions just in a few simple steps. Then take off.
Support DJI Digital Video transmitter.
The flight controller has two independent 9V 2A BEC and 5V 2A BEC, supports various analog image transmissions above 5V, and also supports DJI Air Unit / RunCam Link / Vista.
Real 35A ESC, no false labeling!
6-layer 2oz PCB plus optimized circuit design equals stable and strong current output. The four-channel continuous 140A output can reach 30 seconds.
*Test result comes from SpeedyBee laboratory.
M2 or M3? Why not both?
Have you ever experienced that the stack holes of your frame did not fit the stack you got? This stack is perfectly compatible with M2/M3 screws. What’s more, two sets of M2 and M3 screws + silicone grommets are included in the package!
Dimensions
Wiring Diagram
Specifications
Product Name
SpeedyBee F7 Mini Specs
MCU
STM32F722
IMU(Gyro)
BMI270 for current batches; MPU6000 for old batches before May 2022.
USB Port Type
Type-C
Barometer
N/A
OSD Chip
AT7456E chip
BLE Bluetooth
Supported. Used for Flight Controller configuration(MSP should be enabled with Baud rate 115200 on UART 6)
WIFI
Not supported
Flash FC Firmware Wirelessly
Not supported. Please update firmware for this FC on the PC
Download/Analyze Blackbox
Not supported. Please download and analyze Blackbox data on the PC
DJI Air Unit Soldering Pads
Supported
Flash(for BlackBox)
8MB
Current Sensor
Supported, Scale=250 Offset=-500
BetaFlight Camera Control Pad
Yes(CC pad)
Power Input
3S - 6S Lipo
5V Output
6 groups of 5V output, five +5V pads and 1 BZ+ pad( used for Buzzer). The total current load is 2.5A.
9V Output
2 groups of 9V output, the total current load is 2A.
3.3V Output
Supported. Up to 500mA current load.
ESC Signal Pads
M1 - M4
UART
Full UART * 3(UART1, UART2, UART3)
ESC Telemetry UART
R4(UART4)
I2C
Not supported
LED Pad
Used for WS2812 LED
Buzzer
BZ+ and BZ- pad used for 5V Buzzer
BOOT Button
Used to enter DFU mode
RSSI Input
Not supported
SmartPort
Use any TX pad of UART for the SmartPort feature.
Supported Flight Controller Firmware
BetaFlight(Default)
Firmware Target Name
SPEEDYBEEF7MINIV2 for current batches(Gyro: BMI270); SPEEDYBEEF7MINI for old batches(Gyro: MPU6000) before May 2022.
Right away, this is the best 65mm Whoop I know. Not even close.
I ordered two, one is more or less stock, just the PEEK motor screws and V3 cockroach. The second is upgraded to 0702 27000kV but will go back because I like the 25000kV more because of smoother throttle response and perfect betaflight tune.
Now the but:
1. On both quads I had to replace the BeeEye for a spare one because both are out of focus.
2. the yellow props were way too loose and very brittle. I lost two on my maiden. Black, blue and red are very tight (too tight for such a fragile prop) but if you get them on without bending them, they will last.
3. why does the quad not come with the lighter frame right away?
4. PH2.0…. You know the drill.
On that price point, even after the frame and PEEK upgrade I can forgive these quality issues. Especially considering the great tune and quality FC and motors. But be sure to order a replacement cam and props right away.
This was kind of a late night lark. I'd seen this upgrade for the Mk3 for a while and pondered whether it was a gimmick or not, and I'm pleased to say it's a genuinely good upgrade. It has reduced the noise of my Mk3 considerably. I haven't noted any significant increase in print quality, but the old drone of the bed is gone and that's completely worth it.
when i received mine the box and everything was not damaged but when i opened it the canopy was cracked and the VTX did not work when i tried my first battery. I'm alright with the vtx being DOA as all i really wanted was the motors and beeeye camara, But when i reached out to customer service i was blamed for crashing it (even tho i never flew it). beware the QC is total garbage. save your money and buy a Mobula6 from a reputable company like GetFPV for RDQ's. I wasn't going to write a review but after the email i received i don't want anyone else getting scammed.
I had a very personable experience shopping with my drone your team took the time to help me purchase exactly what I and also identified the additional accessories that I may need to purchase that way I would not have post purchase regret. I will definitely be shopping there again for more flight systems and accessories.
