NewBeeDrone AcroBee75 HD O3 Kit Only (No DJI O3 Air Unit)

Introducing the AcroBee75 HD O3 Kit - a compact powerhouse. It's the pioneer whoop featuring  G4 flight controller with upgraded Double N-MOS and MPU6000 Gyro with built-in ELRS2.4 receiver, effortlessly compatible with Dshot600 and bi-directional Dshot. As the tiniest and lightest HD whoop to compatible with DJI O3 unit, it boasts remarkable agility and an impressive flight time of nearly 3.5 minutes. Our expert tuning ensures seamless indoor filming in self-level and acro modes. To optimize performance and visuals, turn on DJI RockSteady via goggle settings. Note that this model is not suitable for outdoor or windy conditions. Plug and Ply with DJI O3 Air Unit. 

DJI O3 installation instruction: 
1. Replace O3 antenna to the BeeTX 5.8Ghz Antenna
2. Unscrew the Acrobee75 HD O3 Canopy
3. Insert the camera(make sure the DJI logo on the back of the camera are point up)
4. Insert the antenna into the canopy first then insert the O3 Air Unit
5. Insert the cable through the gap between the air unit and the canopy, plug in the cable.
6. Install back the canopy and tight up the camera. 


Important Notice: If you experience issues with your drone, do not flash the firmware. Simply perform a factory reset using the configuration tool (e.g., Betaflight Configurator) and then do an accelerometer calibration. For further assistance, please contact our support team.

Acrobee75 HD O3 1
AcroBee75 HD O3 2






Explore and film spaces you never could before in HD! A must-have tool for professionals and hobbyists specializing in indoor space.

 AcroBee75 HD O3



Compared to other O3 HD whoops at 85mm and 80mm, NewBeeDrone engineered DJI O3 into a 75mm frame. This is the new standard for the smallest O3 HD whoop. 

 AcroBee75 HD O3 4



The only HD Micro whoop board with G4 processor. Dual-bearing motors allow less friction in spinning while 3-blade Azi propellors were developed with engineering theory for optimal air-grab and stability. We master-tuned this drone to have the smoovest flight and absolutely no jello in any videos. 

 AcroBee75 HD O3 5




We found the best ratio between the size of drone and its weight distribution. Without DJI O3, the drone can fly up to 8 minutes. Up to 3 minutes with DJI O3 and battery. Choose between 3D printed battery mounts or strap.  

AcroBee75 HD O3 6 




We ensure that you get the best material and components  that are available so you can rely on the drone without troubleshooting or breaking. All parts are available separately as replacements. Additional flexibility with SLS Nylon prints allow cameras to be changed or updated if needed. 

 AcroBee75 HD O3 7




Assembly or tuning not required. Save time and energy so you can focus on your footage. Drone comes with built-in ExpressLRS and ready to pair. Built-in blackbox records data for tuning. Configure to DJI PNP on Betaflight if needed. Don't be afraid of messing up on customization. Reset to factory default (with our tunes and dump files) in one click if something is not right.


AcroBee75 HD O3





Our support team in the United States are here to help. US customers enjoy Unlimited Frame Warranty from our site. For other countries, please ask your local store to see if they offer replacement. 

 AcroBee75 HD O3 10

Specifications:

Drone Size: 75mm
Flight Controller: BeeBrain HD G4 Flight Controller ExpressLRS (ELRS) 2.4G
Frame: Cockroach75 Brushless Frame
Motors: Flow 0804 12000kv Double Ball Bearing Brushless Motor
Propellesr: Azi (Tri-Blade) Micro Propellers 40mm - 1.0mm Shaft
HD VTX & Camera: DJI O3 Air Unit
Canopy: NewBeeDrone Acrobee75 HD O3 Canopy
Total Weight without battery: 70.19g
Total Weight with battery: 98.24g - 99g

Recommended battery: 
Tattu 450mAh 7.6V High Voltage 95C 2S1P Lipo Battery Pack with XT30 Plug - Long Pack
Tattu 650mAh 7.6V High Voltage 95C 2S1P Lipo Battery Pack with XT30 Plug - Long Pack
Tattu 850mAh 7.6V High Voltage 95C 2S1P Lipo Battery Pack with XT30 Plug - Long Pack
Tattu R-Line 550mAh 7.4V 95C 2S1P Lipo Battery Pack with XT30 Plug

BeeBrain BLV4 HD G4 Flight Controller ELRS2.4G Specifications:


  • MCU: STM32G474
  • ESC Firmware: Z-H-40 - Bluejay 0.19.2 48kHz.
  • ESC Specifications: 1 channel 20A ESC
  • Receiver: NBD ExpressLRS 3.0 Diversity (non-SPl)
  • Receiver Antenna: 1x BeeT-Antenna 1x 2.4G receiver antenna
  • Flight Controller Weight:7.4g (including antenna and XT30 Battery connector)
  • Flight Controller Size: Outer dimensions :29 x 29 x 7.6 mm
  • Flight Controller Holes: 25.5 x 25.5 mm
  • Battery Input: 1-2S
  • BEC:10V 2A for DJI O3 (under 2S power only)
  • BEC:5V 2A
  • UART1: Free
  • UART2: TX & RX for EXPRESSLRS 3.0 receiver
  • UART3: Free
  • UART4: Free
  • Flight time with Tattu 450mAh 2S battery is 3:00min (at 7v) 

Firmware

BeeBrain BLV4 HD Betaflight 4.4.0 firmware with tune

All new Firmware can be found on NewBeeDrone Github page

What’s included: 

1x NewBeeDrone AcroBee75 HD O3 Without O3 Kit
3x Acrobee75 HD O3 Canopy
1x Extra Battery Strap (for other sized batteries)
4x Azi 40mm Propellers

Warning: This drone has been carefully crafted using only newbeedrone parts. It is important to note that any use of non-compatible parts from other brands may result in technical difficulties. Additionally, should you choose to modify the drone, it is crucial that you assume full responsibility for any resulting issues. It is not advisable to proceed with modifications without the necessary knowledge and expertise. We appreciate your understanding and cooperation in ensuring the safe operation of the drone.

*Note: For outdoor flying, RockSteady is required in order to get the best picture quality(On DJI goggle Menu). The PID tune are base on the current setup. If you change any setting on the drone and it is acting weird, please flash the newest firmware

Video:



Review Video:






Download:

BeeBrain BLV4 HD Betaflight 4.4.0 firmware with tune

Newest Firmware

3D file


Customer Reviews

Based on 1 review
0%
(0)
100%
(1)
0%
(0)
0%
(0)
0%
(0)
D
Dante Keith
Great little drone

This drone it great at the applications I use it for. %28Run and gun%2C and simple gap exploration.%29 I handles out doors quite fine%2C however it does get carried with the wind a little. Whatever though it’s 98grams. The O3 canopy is a bit more brittle%2Fridged than I’d like. Not good for hard landing or crashes but I think NewBeeDrone could improve their material choice. Overall I really like this one. It’s small and the O3 captures what you need.