• Description

A New Cinewhoop Design Philosophy

To date, many ducted cinewhoop frames have been needlessly heavy. Additionally, existing light cinewhoop frames don’t have guarded props for flying around softer targets. Heavy frames leave you with very little room for adaptability to use the frame for your shoots whether it be increased payload capacity or the option for larger batteries. We at NewBeeDrone worked to change that.

The CinemAh Frame - The Most Versatile Cinewhoop Frame

The CinemAh frame is NewBeeDrone’s response to the need for a lighter and more versatile cinewhoop frame to carry a full GoPro. The CinemAh has a unique all-carbon fiber frame structure that allows for easy access to electronics while providing maximum structural strength.

The GoPro Mount (Not Included)

The NewBeeDrone CinemAh cinewhoop TPU GoPro 8 and 9 mounts allow for 4 built-in angles for quick-snap adjustment from 0 deg to 22.5 deg. The capture cam mounts are 2xM2 mounting holes set 20mm apart allowing the community to design any mounting solution for any HD capture cam option. 

Other 3D Printed Accessories (Not Included)

Check out our complete collection of 3D printed accessories for the Cinemah! We've got snap in ducts, lightweight battery straps, and protective duct coverings in addition to action camera mounts.

 

Electronics Mounting:

  • 2 sets of 1x1inch mounting locations
  • Front 20x20 location has M3 mounting for a flight controller and ESC stack.
  • Rear 20x20 location has M2 mounting for Caddx Vista – with rear antenna mount.
  • Camera mounting – single and double screw camera mounting options.
  • Note: The frame does not fit an air unit.

Motor Mounting: 12mm diameter, 4-hole pattern

  • Suggested Motors: 14xx – 20xx

Propeller size:

  • 3inch or 76mm propeller 

Weight: 

  • 78g with Adjustable GoPro Hero8 mount and motor screws
  • 68g without GoPro Hero 8 mount 
  • Downloadable 3D printed TPU snap-in ducts (x4) weigh 24g total – 6g each duct

 

    Build include Parts:

    If you need 3D prints, get them here! 

    3D Printed Parts Files


    3D Printed Parts Design by Third party
    Caddx Peanut Mount by Jason Suter. Thank you Jason!!

    Link to manual.

     

    Build Video: 



    Description

    A New Cinewhoop Design Philosophy

    To date, many ducted cinewhoop frames have been needlessly heavy. Additionally, existing light cinewhoop frames don’t have guarded props for flying around softer targets. Heavy frames leave you with very little room for adaptability to use the frame for your shoots whether it be increased payload capacity or the option for larger batteries. We at NewBeeDrone worked to change that.

    The CinemAh Frame - The Most Versatile Cinewhoop Frame

    The CinemAh frame is NewBeeDrone’s response to the need for a lighter and more versatile cinewhoop frame to carry a full GoPro. The CinemAh has a unique all-carbon fiber frame structure that allows for easy access to electronics while providing maximum structural strength.

    The GoPro Mount (Not Included)

    The NewBeeDrone CinemAh cinewhoop TPU GoPro 8 and 9 mounts allow for 4 built-in angles for quick-snap adjustment from 0 deg to 22.5 deg. The capture cam mounts are 2xM2 mounting holes set 20mm apart allowing the community to design any mounting solution for any HD capture cam option. 

    Other 3D Printed Accessories (Not Included)

    Check out our complete collection of 3D printed accessories for the Cinemah! We've got snap in ducts, lightweight battery straps, and protective duct coverings in addition to action camera mounts.

     

    Electronics Mounting:

    • 2 sets of 1x1inch mounting locations
    • Front 20x20 location has M3 mounting for a flight controller and ESC stack.
    • Rear 20x20 location has M2 mounting for Caddx Vista – with rear antenna mount.
    • Camera mounting – single and double screw camera mounting options.
    • Note: The frame does not fit an air unit.

    Motor Mounting: 12mm diameter, 4-hole pattern

    • Suggested Motors: 14xx – 20xx

    Propeller size:

    • 3inch or 76mm propeller 

    Weight: 

    • 78g with Adjustable GoPro Hero8 mount and motor screws
    • 68g without GoPro Hero 8 mount 
    • Downloadable 3D printed TPU snap-in ducts (x4) weigh 24g total – 6g each duct

     

      Build include Parts:

      If you need 3D prints, get them here! 

      3D Printed Parts Files


      3D Printed Parts Design by Third party
      Caddx Peanut Mount by Jason Suter. Thank you Jason!!

      Link to manual.

       

      Build Video: 



      Customer Reviews

      No reviews yet
      0%
      (0)
      0%
      (0)
      0%
      (0)
      0%
      (0)
      0%
      (0)