NewBeeDrone x Team BlackSheep BeeBrain BLV4 Built in Crossfire Rx
We would like to remind you that our flight controller product is designed to work with our own product line. While we have taken every possible measure to ensure the quality and compatibility of our product line, using third party components may result in incompatibility or improper functioning of the product. such as Camere with different voltage signal will mass up the OSD function, frame from other company that is not fitting well with our FC, Motor plug are not compatible with the JST1.0 on the FC. etc.
We strongly recommend that you verify the compatibility and functioning before any soldering or modification.
Please be aware, drone flight controller will break due to crash, any physical damage or crash will have posibility to destory the hardware. This is also not cover by our warranty. If you find that the product is Dead On Arrival (DOA), we will replace it for you free of charge.
However, we cannot take responsibility for any issues that may arise due to modifications made to the product or the use 3rd party components. In such cases, we will not be able to provide support or warranty coverage.
Thank you for your understanding and for choosing our product. If you have any questions or concerns, please don't hesitate to contact our customer support team.
This product is designed mainly to be a replacement part for the NewBeeDrone x Team BlackSheep AcroBee65 BLV4 Crossfire.
BeeBrain BLV4 CRSF Spec:
VTX: Switchable output power from 5mw- 25mw(for Racing) - SmartMAX(SmartMax up to 400mw) with BeeTX 5.8Ghz Antenna
ESC: 12A BLHeliS Pre-Flash with Bluejay 0.18 target: S-H-40 48kHz
ESC Connector: JST-1.0 3Pin
OSD: NBD7456 Graphical OSD compatible with Betaflight OSD
Receiver: Crossfire Nano receiver with MINIMORTAL T ANTENNA
Flight Controller Weight: 6.5g(Include antennas and battery connector)
Flight Controller Size: Outer dimensions: 29x29x7.6mm
Flight Controller Holes: 25.5x25.5mm
Battery input: 1S
Uart2: Crossfire Nano receiver
Power Connector: NBD-PH2.0 connector
- 1 x BeeBrain BLV4 CRSF Flight Controller
- 4 x Grommet
- 4 x Screw
- 1 x MINIMORTAL T Antenna
- 1 x VTX Antenna
All New firmware can be found on our Github Page
All firmware can be found on our Github Page
I even upgraded mine with Hypertrain BB's and 2 blade props. WAY more power and still 4ish min flight time.
The arrival of this BLV4 was as promised. It showed up…looks like -un blemished. Haven’t installed yet.
Broke my Mob7 FC and replaced it with this. I Used the tuning from happy model, and honestly it wasn’t the same-until I flashed bluejay, and now it floats and is very responsive-I even changed the melody to rick roll 🎵 on battery plugin. Very enjoyable flight, I just wish they had standard connectors for more experimentation without soldering or buying their products.
Welp grab yours while they’re hot! Sell NewBeeDrone out they deserve all the credit.
I had one of these board survive a shorted camera connection some how and every still worked. NBD support offered to replace it in good faith !! Best support team. What are you waiting for? For it to be sold out ? So Buy 2! Remember 1 is none and 2 is one! In the meantime 3 will be mine ! 😎
I couldn’t be happier about the inclusion of Crossfire into a whoop board. I have avoided getting into the mud of ELRS, but it felt like I was going to be stuck doing so until this came along. I also love the fact that it has motor pads allowing for direct solder so you can use any motors you want without having to remove the plugs which isn’t fun. I only fly these on 1S, and so far Ivenbeen very happy with the 2 I have