Our best pre-built drone just got better! Another breakthrough in FPV visuals from DJI with our upgraded frame and electronics. A new standard of Bind-And-Fly drones that are simple to get started with but the durability and performance for enthusiasts.Welcome to the iFlight experience!
Introducing the latest iteration of the Nazgul evoque F4, featuring enhanced performance and a lighter, more compact design.
Highlights
Latest Nazgul Frame for Maximum Protection
The old days are over, getting your electronics full of dirt and wet grass every time you crash. Our latest frame reduces contamination that could build up on your flight controller or ESCs, preventing failure or short circuits. Strategic airflow to keep your components cool and clean without taking any shortcuts in weight or performance. Illuminated side panels and 360-degree TPU protective parts.
DJI O3 HD Air Unit Low-Latency digital transmission
Up to 10 km video transmission range, enjoy a crisp and smooth real-time view in your goggles, even in environments with interference. (Source DJI)
4K Stabilized Video with 155° Ultra-Wide Angle
Together with high-grade imaging performance, it delivers exceptional visuals that will keep your audience on the edge of their seats. (Source DJI)
Secured Battery Plug with Anti-Spark Filter
Plugging in a battery can create a loud spark at the connector which is caused by the high battery current rushing into the low ESR capacitor first as well as filling up ESC capacitance. We’ve added a protective circuit to extend the lifespan of XT60 connectors and prevent rapid voltage or current spikes which can protect your electronics from damage.
Operating Temperature Range: -10° to 40° C (14° to 104° F)
Antennas: DJI O3 Air Unit Dual-Band Antenna
GNSS: GPS+SBAS+Galileo+QZSS+Glonass(Optional)
Recommended batteries:
6S 1050mAh Battery
6S 1400mAh Battery
Video Transmission
Product Name: DJI O3 Air Unit
Communication Bandwidth: Max 40 MHz
FOV (single screen): 155°
Communication Frequency: 2.400-2.4835 GHz (RX only) / 5.725-5.850 GHz (RX and TX)
End-to-End Latency
With DJI FPV Goggles V2:
810p/120fps Video Transmission Quality: The latency is lower than 28 ms.
810p/60fps Video Transmission Quality: The latency is lower than 40 ms.
With DJI Goggles 2:
1080p/100fps Video Transmission Quality: The latency is as low as 30 ms.
1080p/60fps Video Transmission Quality: The latency is as low as 40 ms.
Max Video Transmission Bitrate: 50 Mbps
Max Video Transmission Range:10 km (FCC), 2 km (CE), 6 km (SRRC)
Operating Temperature Range: -10º to 40º C (14° to 104° F)
Power Input: 7.4-26.4 V
Audio Transmission: N/A
Packing List
1 x Evoque F4 6S HD BNF
1 x DJI O3 air unit Antenna
1 x Battery pad
4 x HQ 4x3x3 propeller(Pairs)
2 x Battery strap
Important
All iFlight BNFs are tested before shipment to guarantee the highest quality.
If you still encounter a problem after receiving your shipment, please immediately contact our iFlight customer support at www.iflightrc.freshdesk.com.
Note
1. iFlight products may be used for civilian purposes only and any direct or indirect use of iFlight products for or in connection with the following is prohibited:
(1)Any military combat purpose or military combat related use;
(2)Terrorist activities: The purchaser also shall require its customers or end users to comply with the foregoing requirements.
2. If party A has violated applicable export control or economic sanctions laws and regulations, Party B has the right to immediately suspend delivery of products to Party A or terminate relevant cooperation without any liability.
Right away, this is the best 65mm Whoop I know. Not even close.
I ordered two, one is more or less stock, just the PEEK motor screws and V3 cockroach. The second is upgraded to 0702 27000kV but will go back because I like the 25000kV more because of smoother throttle response and perfect betaflight tune.
Now the but:
1. On both quads I had to replace the BeeEye for a spare one because both are out of focus.
2. the yellow props were way too loose and very brittle. I lost two on my maiden. Black, blue and red are very tight (too tight for such a fragile prop) but if you get them on without bending them, they will last.
3. why does the quad not come with the lighter frame right away?
4. PH2.0…. You know the drill.
On that price point, even after the frame and PEEK upgrade I can forgive these quality issues. Especially considering the great tune and quality FC and motors. But be sure to order a replacement cam and props right away.
This was kind of a late night lark. I'd seen this upgrade for the Mk3 for a while and pondered whether it was a gimmick or not, and I'm pleased to say it's a genuinely good upgrade. It has reduced the noise of my Mk3 considerably. I haven't noted any significant increase in print quality, but the old drone of the bed is gone and that's completely worth it.